Product Category

Got any Questions? Call us Today!

+8618758069661

service@fctel.com.cn

Or leave us a message

Online Message

4E1 to 3FE Converter With Console Management

View : 1,204
Type : E1 to Fiber Ethernet
Description :

This 4e1-3fe converter adopts large-scale FPGA design, adopts reverse multiplexing technology, and binds multiple E1 circuits to transmit 3-channel 10 / 100base Ethernet data.

Overview

    This series of equipment adopts large-scale FPGA design, adopts reverse multiplexing technology, binds multiple E1 circuits to transmit 3-channel 10 / 100base Ethernet data and 1-channel console network management, and realizes the mutual conversion between 1-4 E1 channels and Ethernet optical interfaces. This equipment can transmit the signal from the E1 channel to Ethernet optical interface point-to-point, and realize the interconnection between the E1 channel and Ethernet optical interface. Different from general remote bridge, this equipment supports a flexible configuration of 1-4 E1 channels, can automatically detect the number of E1 and select available E1, and allows a certain transmission delay difference between E1 circuits.
    This equipment provides 4 channels E1 (75 or 120 Ohm) interface, 3 channels Ethernet interface, and a 1-way console network management. The whole machine is stable and reliable, with low power consumption, high integration, and small volume.

Product Photo

4 E1 over 3 FE Ethernet converter 4 E1 over 3 FE Ethernet converter

Features

Integrated circuit based on independent intellectual property rights;

Transparent transmission of Ethernet data in 1-4 E1 circuits is realized;

Reset operation of local and remote equipment can be realized;

Ethernet interface 100Base-FX, supporting VLAN protocol;

Built-in dynamic Ethernet MAC address list (4096), with local data frame filtering function;

The rate of single E1 line is 1984kbit / s, and the bandwidth of 4-channel E1 can reach 7936kbit / s;

Support any setting of Ethernet working mode;

The CRC alarm threshold can be set to automatically isolate the lines with poor transmission quality, and it is cut off in one direction. When the bit error rate in one direction of the 2m branch exceeds the exit limit, only that direction will be cut off, and the other direction will not be affected; that is, the two directions of Ethernet transmission can be asymmetric;

The transmission delay difference of 4-channel E1 is allowed to be 100ms. When the difference exceeds the allowable range, the system can automatically stop sending data on E1 with excessive delay;

The E1 interface conforms to ITU-T G.703, g.704, and g.823, and does not support the use of signaling time slots;

E1 interface module includes built-in clock recovery circuit and HDB3 encoding and decoding circuit;

Provide console management interface for easy installation and opening;

It has the function of viewing and displaying the working status of remote equipment at the local end;

The equipment supports hot swap of E1 channel, and automatically detects the effective E1 channel without interruption of data transmission;

It supports the flexible configuration of 1 to 4-channel E1, automatically detects the number and delay of E1 and selects available E1 during reset;

Parameters

E1 interface
Equipment interface: the equipment interface meets the recommendation of G.703
Rate: 2048kb / s ± 50ppm
Code type: HDB3
Impedance: unbalanced 75 / balanced 120
Unbalanced coaxial interface adapter for 75-2 / 3 coaxial cable
Jitter characteristics: meet the recommendations of g.742 and g.823
Allowable attenuation of input port: 0 ~ 6dbm

10/100M Ethernet
Protocol: IEEE 802.3az, IEEE 802.1Q (VLAN)
adaptive
MAC address table: can learn 4096 MAC
addresses
Physical interface: RJ45 supports auto-mdix

Electrical and mechanical characteristics
System power supply: ac180v ~ 260V; DC – 48V; DC + 24V
Power consumption: ≤ 5W
Appearance structure: (length × width × height) 216 * 138 * 41mm desktop type

 

Environmental indicators
Working temperature: – 10 ℃ – + 60 ℃
Storage temperature: – 40 ℃ – + 85 ℃
Working humidity: 0% – 95% (no condensation)
MTBF: > 100000 hours

Specifications

Product Function Description

4 channel  E1 to 3 channel  Ethernet + 1 channel console network management

Business port description

 Conversion of 4E1 to 3 Ethernet + 1 console interface, bandwidth 8.192m, adaptive, VLAN support, desktop type, – 48V or AC220V power supply (optional)

Power Supply

AC220V / DC-48V / DC+24V

Product Size

216*138*41mm desktop type

Weight

1.3Kg /PCS

Application

application of 4 E1 over 3 10/100M Ethernet converter

                   

Leave a Message

If you are interested in any product, please contact us. We will introduce our products to you in more detail