It provides 16 E1 interfaces, 1 digital business phone, 12 10/100M Fast Ethernet interfaces (line speed 100m), and 8 channels telephone.
This product is a point-to-point optical transmission device that is developed on the basis of PDH special VLSI for optical fiber transmission. It provides 16 E1 interfaces, 1 digital business phone, 12 10/100M Fast Ethernet interfaces (line speed 100m), and 8-channel telephone. The Ethernet interface is the switch port, which can support the VLAN division. It has a perfect alarm function. It has stable and reliable operation, low power consumption, high integration, and small size.
● Integrated circuit based on independent intellectual property rights;
● It provides 2 optical interfaces, double optical port 1 + 1 protection (APS), ALS (automatic laser shutdown/reduction) functions: after detecting the optical fiber interruption of the optical path, the optical transmitter has no output power, and can automatically return to normal state after the optical fiber is recovered;
● The ethernet interface rate is 10/100M, full duplex/half duplex adaptive; the 12-channel network is the switch port and can also be divided into VLAN, which can be set as 12-channel logical isolation;
● E1 interface meets the recommendation of G.703 and adopts full digital clock recovery and smooth phase-locked technology;
● When the optical signal is lost, it can detect whether the opposite equipment is powered down or the optical fiber is blocked, and indicate the alarm through the indicator light;
● It has the function of viewing and displaying the working status of remote equipment at the local end;
● 8channel voice telephone; voice telephone port supports FXO port and FXS port, FXO port connects with SPC exchange, FXS port connects with user’s telephone;
● When the optical signal is lost, it can detect whether the opposite equipment is powered down or the optical fiber is blocked, and indicate the alarm through the indicator light;
● It has the function of viewing and displaying the working status of remote equipment at the local end;
● It provides a remote interface loopback function.
● It provides a console management interface for easy installation and opening, and provides network management interface (BNC) for network management monitoring;
● The transmission distance without a relay can reach 2 ~ 120 km;
● Multiple power supply modes: AC220V, dc-48v / DC24 V, etc.; support AC + DC, AC + AC, DC + DC and other dual power backup modes;
● Dc-48v / DC24 V power supply has the function of automatic polarity detection, so it is unnecessary to distinguish the positive and negative poles during installation.
Multi-mode Fiber
50/125um, 62.5/125um,
Maximum transmission distance: 5Km @ 62.5 / 125um single mode fiber,attenuation (3dbm/km)
Wave Length: 820nm
Transmitting power: -12dBm (Min) ~-9dBm (Max)
Receiver sensitivity: -28dBm (Min)
Link budget: 16dBm
Single-mode Fiber
8/125um, 9/125um
Maximum transmission distance: 40Km
Transmission distance: 40Km @ 9 / 125um single mode fiber, attenuation (0.35dbm/km)
Wave Length: 1310nm
Transmitting power: -9dBm (Min) ~-8dBm (Max)
Receiver sensitivity: -27dBm (Min)
Link budget: 18dBm
Interface Standard: comply with protocol G.703;
Interface Rate: n*64Kbps±50ppm;
Interface Code: HDB3;
E1 Impedance: 75Ω (unbalance), 120Ω (balance);
Jitter tolerance: In accord with protocol G.742 and G.823
Input Allowed Attenuation: 0~6dBm
Interface rate: 10/100/1000 Mbps, half/full duplex auto-negotiation
Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)
MAC Address Table: 4096
Connector: RJ45, support Auto-MDIX
Ring voltage: 75V
Ring frequency: 25HZ
Two-line Impedance: 600 Ohm (pick up)
Return loss: 40 dB
Ring detect voltage: 35V
Ring detection frequency: 17HZ-60HZ
Two-line Impedance: 600 Ohm (pick up)
Return loss: 40 dB
Working temperature: -10°C ~ 60°C
Working Humidity: 5%~95 % (no condensation)
Storage temperature: -40°C ~ 85°C
Storage Humidity: 5%~95 % (no condensation)
Model |
FCP-E16F12 |
Function Description |
Provide 16e1 + 12 * 10/100M Ethernet + 8 channel voice, 19 inch rack type, – 48V or AC220V power supply (optional) |
Port Description |
One 1 * 9 100m optical port, 16 E1 interfaces (75 Ω), 12 100M Ethernet interfaces, 8 telephone interfaces |
Power |
AC220V or dc-48v (power supply optional), support power redundancy backup |
Dimension |
Product Size: 485X200X45mm(WXDXH) 19 1U |
Weight |
2.7KG |
Before ordering or wiring, confirm the exact model and configuration, interface pinout, optical or network compatibility, power input and installation conditions. Optional configurations are not interchangeable.
Browse FCTEL technical documents · Request the current model-specific datasheet and wiring diagram
Share your devices, interfaces or quantity—our team will help you choose a suitable solution.
We use your information only to respond to this inquiry.
Inquire Now
