Product Category

Got any Questions? Call us Today!

+8618758069661

service@fctel.com.cn

Or leave us a message

Online Message

8 Channel Dry Contact to Ethernet Converter

View : 1,250
Type : Dry Contact Closure over IP
Description :

The converged 8-channel dry contact equipment can transmit up to 8 channel dry contact in the two-layer Ethernet network, and the middle can be connected with the layer-2 network switch

Overview

The converged 8-channel dry contact equipment can transmit up to 8-channel dry contact in the two-layer Ethernet network, and the middle can be connected with the layer-2 network switch.

 

The product solves the problems of electromagnetic interference, ground environment interference, and lightning damage, and improves the reliability, security, and confidentiality of data communication. It can be widely used in various industrial control, process control and traffic control, especially suitable for banks, electric power and departments and systems with special requirements for electromagnetic interference environment.

Photo

Dry Contact to Ethernet (IP) Converter Dry Contact to Ethernet (IP) Converter

Features

● Integrated circuit based on independent intellectual property rights;

● The equipment shall provide at most 8ch dry contact signal, 2 100M Ethernet electrical ports, and 1 100M Ethernet SFP optical port;

● Input switch value automatic detection, when the input state, the switch output is the state, which is convenient for project opening;

● When the switch value is in the start-up state or when the optical fiber is not connected, other switch states are stable, and there is no disorderly action state;

● It can support 8ch dry contact switching value or wet pulse contact impulse (Optical MOS Relay), with high reliability and high operation speed;

● Each motherboard can be connected with the node equipment with a total switch quantity of no more than 8 channels and the equipment at the convergence end through the switch;

● Automatic reset function of anti-crash monitoring, with heartbeat packet sending and detection inside;

● Switch value interface lightning protection meets iec61000-4-5 (8 / 20 μ s) differential mode: 6kV, impedance (2 Ω); common mode: 6kV, impedance (2 Ω);

● AC 220 V, DC – 48V, DC + 24 V can be selected. There is no positive and negative pole in the DC power supply

Parameters

Fiber type

Working wavelength: 1310nm, 1550nm

Speed: 100M, full duplex or half repeater mode

Protocol: Support IEEE 802.3, IEEE 802.1Q (VLAN)

MAC address table: can learn 4096 MAC addresses

Physical interface: SFP

The distance of optical fiber transmission is limited by the loss of optical path and the additional loss caused by connecting terminals, connectors and patch boards. The transmission distance may also be limited by the fiber bandwidth

 

● 10/100M Ethernet                   

Protocol: IEEE 802.3az, IEEE 802.1Q (VLAN)

Rate: 10/100M adaptive, full/half duplex fully adaptive

MAC address table: can learn 4096 MAC addresses

Physical interface: RJ45 supports auto mdix

 

Dry Contact Interface

Output interface type:

Dry contact: Optical MOS Relay Output

(maximum internal resistance 25 Ω)

Wet contact impulse: output of Optical MOS

Relay, 0-vcc (VCC is the power supply voltage of the machine)

Response time signal relay dry contact output: <1.2ms,

Optical MOS Relay Output < 0.6ms

The dry contact output of the switch signal relay is 30VDC/0.5A;

the output of the optical MOS Relay is 245vdc/0.12A

Maximum switching frequency: 50 Hz

Output surge protection: TVs + solid discharge tube protection

Physical interface: terminal block

 

Power

System power supply: ac180v ~ 260V; DC – 48V; DC + 24V

Power consumption: ≤ 10W

 

Environmental Indicators

Working temperature: – 40 ℃ ~ 85 ℃

Working humidity: 5% – 95% (no condensation)

Storage temperature: – 40 ℃ ~ 85 ℃

Storage humidity: 5% – 95% (no condensation

Specification

Product Number

KOE-8

Product Function Description

Transmit 8-channel dry contact signal over Ethernet

Port Description

1 Ethernet SFP port, 2  Ethernet ports, and 8 dry contact ports

Power Supply

AC220V or dc-48v (power supply optional), support power redundancy backup

Product Size

(length × width × height) 220 * 135 * 31mm desktop type

Weight

1.6Kg /PCS

Application

APPLICATION OF Dry Contact to Ethernet (IP) Converter

                   

Leave a Message

If you are interested in any product, please contact us. We will introduce our products to you in more detail