Product Category

Got any Questions? Call us Today!

+8618758069661

service@fctel.com.cn

Or leave us a message

Online Message

1*FE + 1*GE Fiber Media Converter (Full Physical Isolation)

View : 497
Type : Special function serials
Description :

This series of products are Ethernet IEEE802.3 media converters. The equipment has 4 electrical Ethernet ports, of which 1,2 ports are Gigabit and 3,4 ports are 100M to achieve physical isolation.

Overview

This series of products are Ethernet IEEE802.3 media converters. The equipment has 4 electrical Ethernet ports, of which 1,2 ports are Gigabit and 3,4 ports are 100M to achieve physical isolation. They can achieve bidirectional bandwidths of 1000M and 100M respectively, and the fiber distance (20/40/60/80/100 km), the total bandwidth is 1100M in both directions.

Two Ethernet electrical ports have their own independent Gigabit and 100M bandwidths. Through a single optical fiber transmission, the Ethernet signals received by the opposite end are also completely independent, without mutual interference and mutual influence, that is, physical isolation.The equipment is based on the Ethernet switch chip + FPGA solution, with remote OAM frame management function, supports Console network management/SNMP network management, and can also be interconnected with 2U plug-in card type 1 optical 2 electrical transceivers with SNMP network management. It can be connected to SNMP software. Manage to this device.

Photo

    Fiber Media Converter (Full Physical Isolation) Fiber Media Converter (Full Physical Isolation)    

Features

Integrated circuits based on independent intellectual property rights;
Provide link aggregation channels for network switches, with a bidirectional bandwidth of 1100M, and 2 groups of physically isolated network services transmitted by the same optical fiber line;
It can provide physical isolation, two-line speed 1000 and line-speed 100M Ethernet channel optical port bandwidth 1.5G, two Ethernet completely independent;
The Ethernet electrical port supports auto-negotiation of speed and duplex mode, and the Ethernet port supports AUTO-MDIX (crossover and direct connection self-adaptation);
The device has a power failure detection function, which can detect when the optical signal is lost, the peer device is powered down or the fiber is blocked;
Support ultra-long frame transmission, fully compatible forwarding of various extended protocol data frames;
The optical interface supports three fiber transmission modes: multi-mode dual fiber, single-mode dual fiber, and single-mode single fiber. SC/ST/FC/LC interfaces are optional, and various optical interface configurations such as different wavelengths and luminous powers;
Abundant working status indicators, which can easily and accurately understand the working status of equipment interfaces and links;
It can realize remote network management function, with 2U card configuration, rack-mounted equipment network management interface adopts SNMP;
Ethernet interface with three-level lightning protection, anti-radar to GB/T17626.5 (IEC61000-4-5) short-circuit current wave 8/20μs, open-circuit peak output voltage 6KV standard
The built-in power supply has multiple power options: AC220V, DC-48V/DC+24V/DC+V12, etc.; A

Parameters

● Fiber Interface
Number of Fiber Ports: 1
Fiber core: Single fiber/dual fiber
Connector: FC/SC/ST/LC(SFP)
Wavelength: 850nm/1310nm multi-mode;1310nm/1550nm single-mode
Transmission distance:20~100Km
Typical output power:
Single mode 1310/1550nm: >-9dBm
Multi-mode 850nm:-18dBm
Multi-mode 1310nm:-25dBm
Receiver Sensitivity: -28dBm~- 40dBm

● 10/100/1000M Ethernet Interface
Protocol: Complies with IEEE 802.3ab, IEEE802.3z
Rate: 10/100/1000M adaptive, full/half duplex fully adaptive;
MAC Address Table: 4K
Physical interface: RJ45 seat, support Auto-MDIX

● Environmental Indicators

Operating temperature: -10 ℃ – +60 ℃
Storage temperature: -40 ℃ – +85 ℃
Humidity: 0% -95% (non-condensing)
MTBF:> 100,000 hours

Specification

Functional Description Physically isolated 1* FE and 1* GE Ethernet on fiber
Port Description

1 fiber interfaces; 1FE Ethernet; 1GE Ethernet, one Console interface;

Power

Power supply: AC180V ~ 260V;DC –48V
Power consumption: ≤10W

Dimension

(L × W × H) 216 * 138 * 41 mm Desktop

Weight

0.95Kg / PCS

Application

application of Fiber Media Converter (Full Physical Isolation)

                   

Leave a Message

If you are interested in any product, please contact us. We will introduce our products to you in more detail