Product Category

Got any Questions? Call us Today!

+8618758069661

service@fctel.com.cn

Or leave us a message

Online Message

4E1-FE Double Impedance Interface Converter

View : 301
Type : Multi E1-Ethernet Bridge
Description :

This 4E1-FE interface converter is based on FPGA, using reverse direction multiplexing technology to bundle multiple E1 circuits to transmit the Ethernet data of 100BASE-TX.

Overview

     This interface converter is based on FPGA, using reverse direction multiplexing technology to bundle multiple E1 circuits to transmit the Ethernet data of 100BASE-TX. It can realize 1-8E1 channels to convert between Ethernet optical interface. This device can transmit the transceiver signal point to point to Ethernet optical interface to make E1 channels interconnected with Ethernet optical interface. Different from general remote network bridge, this device can support 1-8Channel E1 channel configuration, can automatically detect the number of E1, and select the E1 available. It allows E1 lines transmission time delay difference. delay difference.

Product Photo

4 E1 to fe Ethernet Double Impedance Interface Converter 4 E1 to fe Ethernet Double Impedance Interface Converter

Features

Based on self-copyright IC
To achieve Ethernet data transparent transmission in 1-8E1 circuits
Can realize the local and the remote device reset
Ethernet Interface is 100BASE-FX, support VLAN protocol
Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering function
Single Channel lines rate is 1984Kbit/s, 4Channel Bandwidth is up to 7936Kbit/s
Support all set of Ethernet Work Mode
CRC automatic alarm threshold can be set to isolate the poor quality transmission lines and cut off a single direction. When the 2M branch circuit one direction error rate exceeds the threshold, cutting off this direction the other direction is not affected; that is to say, both of the Ethernetdirection transmission can be asymmetric
Allow 16Channel E1 transmission time delay difference 100ms. When the margin exceeds the allowed range, the system can automatically stop on the E1 that time delay is too large to send data
E1 interface conforms to ITU-T G.703, G.704 and G.823, not support the use of signal timeslot
E1 interface module with inter-set clock recovery circuit and HDB3 code circuit
Support E1 channel hot-plug in the device, and automatically detects the effective
channel and will not interrupt data transmission
Can support 1-8Channel E1 channel configuration, can automatically detect the number of E1 and select the E1 available;

Parameters

●E1 Interface
Interface Standard: comply with protocol G.703;
Interface Rate: n*64Kbps±50ppm;
Interface Code: HDB3;
E1 Impedance: 75Ω (unbalance), 120Ω (balance);
Jitter tolerance: In accord with protocol G.742 and G.823Allowed Attenuation: 0~6dBm

●Ethernet interface(10/100M)
Interface rate: 10/100 Mbps, half/full duplex auto-negotiation
Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)
MAC Address Capability: 4096
Connector: RJ45, support Auto-MDIX

●Working environment
Working temperature: -10°C ~ 50°C
Working Humidity: 5%~95 % (no condensation)
Storage temperature: -40°C ~ 80°C
Storage Humidity: 5%~95 % (no condensation)

Specifications

Model

Model Number: FCC-E4F1

Port Description

4E1 interface;1*FE Interface

Description

Achieve 4E1 turn convert the Ethernet interface,  double impedance, support 75ohm and 120ohm

Power

Power supply: AC180V ~ 260V;DC –48V;DC +24V

Power consumption: ≤10W

Dimension

Product Size: 19 inch 1U   483X138X44mm (WXDXH)

Application

application of 4 E1 to fe Ethernet Double Impedance Interface Converter

Leave a Message

If you are interested in any product, please contact us. We will introduce our products to you in more detail