Product Category

Got any Questions? Call us Today!

+8618758069661

service@fctel.com.cn

Or leave us a message

Online Message

Ethernet to E1 Converter (Framed E1)

View : 1,747
Type : Single E1-Ethernet Bridge
Description :

This device provides one framed E1 interface and one Ethernet interface, capable of transmitting 10/100base-T Ethernet data over framed E1.

Overview

This device provides one framed E1 interface and one Ethernet interface, capable of transmitting 10/100base-T Ethernet data over framed E1. It is a high-performance and self-learning Ethernet bridge. As an Ethernet extension device, this device utilizes existing networks (PDH/SDH/microwave, etc.) to provide E1 channels and achieve Ethernet interconnection between two ends at a lower cost. The device has a built-in loopback test function, providing convenience for engineering commissioning and daily maintenance.

Photo

Framed E1 Ethernet ConverterFramed E1 Ethernet Converter

Features

E1 supports any timeslot set, the rate is 64K-2048K;

It can enable monitoring and control of the remote device, while OAM management data doesn’t occupy the user’s timeslot and save E1 bandwidth;

It has the function of E1 interface loopback check, avoiding the device crashing because of interface loopback;

It can differentiate between remote device power loss and E1 disconnection during signal loss;

It can be configured to not send a LINK signal to the Ethernet interface when there is a fault in the E1 line;

The Ethernet interface supports jumbo frames (2036 Bytes);

4-channel 10/100M Ethernet interface can isolate each other to realize communication independently;

Ethernet interface supports 10/100M, half/full duplex auto-Negotiation, and AUTO-MDIX (auto-negotiation of crossover and straight-through connections);

2 clock modes are available: E1 master clock and E1 line slave clock;

It has 3 loopback modes: E1 local loopback (ANA), Ethernet local loopback (DIG), and remote Ethernet loopback (REM);

It has an internal Ethernet data monitoring auto-reset function to prevent device crashes;

It enables local device to monitor the temperature and voltage of remote device;

It supports both 120Ω/balanced and 75Ω/unbalanced impedance, without the need for additional configuration;

● Support SNMP Network Management.

Parameters

● E1 Interface

Interface Standard: Comply with Protocol G.703;

Rate: n*64Kbps±50ppm;

Line Code: HDB3;

E1 Impedance: 75Ω (unbalance), 120Ω (balance);

Jitter Performance: Compliant with G.742 and G.823 recommendations

Input Port Attenuation Allowed: 0~6dBm

 

● Ethernet Interface (10/100M)

Interface rate: 10/100 Mbps, half/full duplex auto-negotiation

Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)

MAC Address Table: 4096

Connector: RJ45, support Auto-MDIX

 

● Working Environment

Working temperature: -10°C ~ 50°C

Working Humidity: 5%~95 % (no condensation)

Storage temperature: -40°C ~ 80°C

Storage Humidity: 5%~95 % (no condensation)

Specifications

Model

FCC-E1fF1

Function Description

1 channel framed E1-FE interface converter, N*64k rate setting,With E1 loopback detection function

Port Description

1 E1 interface, 1 FE Interface

Power Supply

Power supply: AC180V ~ 260V; DC –48V; DC +24V

Power consumption: ≤10W

Dimension

Product Size: desktop type 216X140X31mm (WXDXH),1.1KG/piece

Application

application of Framed 1 channel E1 Ethernet Converter

 

application of Framed 1 channel E1 Ethernet Converter

 

application of Framed 1 channel E1 Ethernet Converter

                   

Leave a Message

If you are interested in any product, please contact us. We will introduce our products to you in more detail